您已在下面突出显示的字段中输入包含无效字符的值。 请仅使用有效字符修改您的选择。

产品可能与您的搜索条件并不完全匹配

您买过此产品。 在订单历史记录中查看

 
 

NB3N4666CDTR2G

驱动器, 四线路接收器, 差分, LVDS, LVPECL, 400Mbps, 3.3ns延迟, 3.3V电源, TSSOP-16

ONSEMI NB3N4666CDTR2G
×
×

图片仅用于图解说明,详见产品说明。

制造商:
ONSEMI ONSEMI
制造商产品编号:
NB3N4666CDTR2G
库存编号
2627905
查看所有技术文档

产品概述

The NB3N4666CDTR2G is a 3.3V quad LVCMOS differential line receiver translator in 16 pin TSSOP package. The NB3N4666C receiver incorporates input fail-safe protection circuit that provides a known output voltage under input open circuit, short and terminated (100 ohm) conditions. The four independent inputs accept differential signals such as M-LVDS, LVDS, LVPECL and HCSL and translates them to a single ended 3.3V LVCMOS. The NB3N4666C also offers active-high and active-low enable/disable inputs (EN and active-low EN) that allow users to control outputs of all four receivers. These inputs enable or disable the receivers and switch outputs to an active or high impedance state respectively. The high impedance mode feature helps to reduce quiescent power consumption to less than 10mW when outputs of one or more. It is used in point-to-point data transmission, backplane receivers, clock distribution networks and multidrop buses.
  • Maximum clock frequency of 200MHz
  • 25ps typical channel to channel skew and 3.3ns maximum propagation delay
  • Data rates up to 400Mbps (200MHz) and low power consumption
  • Power supply voltage of 2.97V to 3.63V (3.3V ±10%)
  • High impedance outputs when disabled
  • Low quiescent power less than 10mW
  • Supports open, short and terminated input fail-safe
  • 10mA no load supply (all receivers enabled) and 3mA no load supply (all receivers disabled)
  • Channel to channel skew of 25ps and part to part skew of 50ps
  • Ambient operating temperature from -40°C to +85°C

应用

通信与网络

警告

Market demand for this product has caused an extension in leadtimes. Delivery dates may fluctuate. Product exempt from discounts.

产品信息

想要查看类似产品?只需在下方选择所需属性并点击按钮 ×


:
-

:
-

:
-

:
MSL 1 -无限制

查找类似产品 选择并修改以上属性即可查找类似产品。

技术文档 (1)

CAD 下载

×

条款

CAD Models - Notice
CAD Models and drawings are provided to you on a revocable limited licence for your internal use only but remain the property of the manufacturer who retain all intellectual property rights and ownership. They are provided to assist you in decision making and as design guide but are not guaranteed to be error free, accurate or up to date and is not intended to be taken as advice.
Use of these CAD models and other options provided are downloaded and used entirely at your own risk and by continuing you confirm acceptance of the above.

接受 取消
包装类型 切割卷带

可延期交货

交付周期内将会有更多库存,大约为 23-6-26

由于市场条件的影响,交货时间仅供一般指导,可能会在短时间内发生变化

有货时请通知我

CNY30.87 ( 不含税  ) CNY34.88 ( 含税 )

定价不可用。 请联系客户服务

包装规格:
单件(切割供应)
多件: 5 最低: 5
数量 价钱 (不含税) (含税) 您所支付金额(含增值税) (不含税)
 
 
5+ CNY30.87 CNY34.88
优惠价格
合约价格
仅限网络价格
仅限网络合约价格
  ( )
25+ CNY30.02 CNY33.92
优惠价格
合约价格
仅限网络价格
仅限网络合约价格
  ( )
 
 

定价不可用。 请联系客户服务

No longer stocked:: No Longer Manufactured::
添加到购物篮 添加到购物篮 预订
添加
受限制物品
添加部件编号/注释行
总价: ( 不含税  )
总价: ( 含税 )
总价: --